Micromembrane absorber with deep-permeation nanostructure assembled by flowing synthesis

A micromembrane adsorber with deep-permeation nanostructure (DPNS) has been successfully fabricated by flowing synthesis. The nanoparticles are in-situ assembled in membrane pores and immobilized in each membrane pore along the direction of membrane thickness. The nanoparticles with a lower size and thinner size distribution can be achieved owing to the confined space effect of the membrane pores. As a concept-of-proof, the nano ZIF-8 and ZIF-67 are fabricated in porous membrane pores for methyl orange (MO) and rhodamine B (RhB) adsorption. The adsorption rate is increased significantly owing to the enhanced contact and mass transfer in the confined space. The adsorption capacity for the RhB is also increased, since the size of the nanoparticles assembled in membrane pores is smaller with more active sites exposed. This micromembrane adsorber with DPNS has good reusability and can provide a promising prospect for industrial application.     

富芳烃重油组分结构调变对中间相沥青形成的影响机制

对重油富芳烃组分转化为次生沥青及其氢化改性沥青的热转化行为进行了比较，并对热转化过程中体系化学结构组成特征对中间相形成的影响进行了研究。采用红外光谱及氢核磁共振波谱，对比分析了次生沥青及其氢化改性沥青的化学结构组成特征；借助偏光显微镜、X射线衍射，考察了两体系中间相沥青的形成过程。结果表明：控制体系短烷基侧链含量可有效抑制过度炭化的发生，提高炭化产物的微观有序度；短烷基侧链可以持续稳定释放出小分子自由基，对大分子自由基反应进行调控，显著提升炭化产物微观结构的均一性。     

Electrorheological response behavior of H2Ti2O5@MoS2@SiO2 core-shell nanoparticles

In this paper, a novel H₂Ti₂O₅@MoS₂@SiO₂ ternary composite material was prepared by a combination of dual hydrothermal method and controlled hydrolysis method, in which H₂Ti₂O₅ nanotubes are tightly combined with hierarchical molybdenum disulfide, and the unique structure of titanate nano whiskers, including the loosely bound alkali metal ions between the titanate layers with high dielectric constant and the large aspect ratio, which induce active response to the electric field. Flower-like molybdenum disulfide provides electrical conductivity, and silicon dioxide as a insulative coating layer can suppress excessive the electrical conductivity of the two-dimensional material. The morphological evolution was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results of showed that the sheet-shaped molybdenum disulfide coated with curved H₂Ti₂O₅ nanotubes showed a honeycomb structure with uniform size. Silicon oxide acts as a cladding layer to increase the thickness of the flakes. The existence of H₂Ti₂O₅, molybdenum disulfide and silicon dioxide is confirmed by X-ray powder diffractometer (XRD) and Fourier transform infrared spectroscopy (FT-IR). The prepared product was confirmed by XPS, BET test and electrorheological rheometer. Core/shell nanoparticles not only exert the active response characteristics of titanate nanoparticles and molybdenum disulfide to electric field, but also inherit the excellent characteristics of a core-shell structure produced by the interface polarization and the synergistic effect of the polar groups on the surface of the two-dimensional material further enhance the electrorheological effect.     

Two Methods,One Goal: Structural Differences between Cocrystallization and Crystal Soaking to Discover Ligand Binding Poses

In lead optimization, protein crystallography is an indispensable tool to analyze drug binding. Binding modes and non-covalent interaction inventories are essential to design follow-up synthesis candidates. Two protocols are commonly applied to produce protein–ligand complexes: cocrystallization and soaking. Because of its time and cost effectiveness, soaking is the more popular method. Taking eight ligand hinge binders of protein kinase A, we demonstrate that cocrystallization is superior. Particularly for flexible proteins, such as kinases, and larger ligands cocrystallization captures more reliable the correct binding pose and induced protein adaptations. The geometrical discrepancies between soaking and cocrystallization appear smaller for fragment-sized ligands. For larger flexible ligands that trigger conformational changes of the protein, soaking can be misleading and underestimates the number of possible polar interactions due to inadequate, highly impaired positions of protein amino-acid side and main chain atoms. Thus, if applicable cocrystallization should be the gold standard to study protein–ligand complexes.     

Investigation of the microwave dielectric properties of the Li4x/3Zn2−2xTi1+2x/3O4 system by P–V–L theory and vibration spectroscopy

Li_4x/3Zn_2–2xTi_1+2x/3O₄ microwave dielectric ceramics with a spinel phase were prepared via a high-temperature solid-phase method. P–V–L theory, vibration spectra, and XPS were utilized to establish the links between the intrinsic and extrinsic factors and the microwave dielectric properties. According to the characterization, the change in permittivity (ε_r) was ascribed to the increase in the average bond ionicity of Ti–O(Af_iTi-O) and the polar mode of the lattice vibration; the change in quality factor(Q × f) resulted from the change in the Ti–O lattice energy (AU_Ti-O) and existence of oxygen vacancy; the increase in temperature coefficient of the resonance frequency (τ_f) was triggered by the increase in the Ti–O bond energy. The Li_0.6Zn_1.1Ti_1.3O₄ ceramics (x = 0.45) sintered at 1125 °C finally obtained optimal microwave dielectric constants of ε_r = 17.3, Q × f = 76,318 GHz and τ_f = -58 ppm/°C.     

Effect of lattice structure evolution and stacking fault energy on the properties of Cu–ZrO2/GNP nanocomposites

A hybrid nanocomposite comprising nanosized ZrO₂ and graphene nanoplatelet (GNP)-reinforced Cu matrix was synthesised via powder metallurgy. The influence of sintering temperature and GNP content on the electrical and mechanical behaviour of the Cu–ZrO₂/GNP nanocomposite was investigated. The ZrO₂ concentration was fixed at 10% for all the composites. Upon increasing the GNP concentration up to 0.5%, a significant improvement was observed in the compressive strength, microhardness, and electrical conductivity of the composite. Furthermore, the properties were significantly improved by increasing the sintering temperature from 900 to 1000 °C. The compressive strength, hardness, and electrical conductivity of Cu–10%ZrO₂/0.5%GNP were higher than those of the Cu–ZrO₂ nanocomposite by 60, 21, and 23.8%, respectively. This improvement in the mechanical properties is because of the decrease in the crystallite size and dislocation spacing, which increases the dislocation density, thereby increasing the impedance towards dislocation movement. The lower stacking fault energy of the hybrid nanocomposites enables easier electron transfer within and between the Cu grains, resulting in an improved electrical conductivity. The enhancement in strength and electrical conductivity were aided by the GNPs and ZrO₂ nanoparticles that were dispersed widely in the Cu matrix.     

Interfacial microstructure and mechanical properties of Ti3SiC2 ceramic and TC11 alloy joint diffusion bonded with a Cu interlayer

Reliable joints of Ti₃SiC₂ ceramic and TC11 alloy were diffusion bonded with a 50 μm thick Cu interlayer. The typical interfacial structure of the diffusion boned joint, which was dependent on the interdiffusion and chemical reactions between Al, Si and Ti atoms from the base materials and Cu interlayer, was TC11/α-Ti + β-Ti + Ti₂Cu + TiCu/Ti₅Si₄ + TiSiCu/Cu(s, s)/Ti₃SiC₂. The influence of bonding temperature and time on the interfacial structure and mechanical properties of Ti₃SiC₂/Cu/TC11 joint was analyzed. With the increase of bonding temperature and time, the joint shear strength was gradually increased due to enhanced atomic diffusion. However, the thickness of Ti₅Si₄ and TiSiCu layers with high microhardness increased for a long holding time, resulting in the reduction of bonding strength. The maximum shear strength of 251 ± 6 MPa was obtained for the joint diffusion bonded at 850 °C for 60 min, and fracture primarily occurred at the diffusion layer adjacent to the Ti₃SiC₂ substrate. This work provided an economical and convenient solution for broadening the engineering application of Ti₃SiC₂ ceramic.     

Strong tribocatalytic dye degradation by tungsten bronze Ba4Nd2Fe2Nb8O30

The triboelectric effect has recently demonstrated its great potential in environmental remediation and even new energy applications for triggering a number of catalytic reactions by utilizing trivial mechanical energy. In this study, Ba₄Nd₂Fe₂Nb₈O₃₀ (BNFN) submicron powders were used to degrade organic dyes via the tribocatalytic effect. Under the frictional excitation of three PTFE stirring rods in a 5 mg/L RhB dye solution, BNFN demonstrates a high tribocatalytic degradation efficiency of 97% in 2 h. Hydroxyl radicals (?OH) and superoxide radicals (?O₂－) were also detected during the catalysis process, which proves that triboelectric energy stimulates BNFN to generate electron-hole pairs. The tribocatalysis of tungsten bronze BNFN submicron powders provides a novel and efficient method for the degradation of wastewater dye by utilizing trivial mechanical energy.     

Preparation of carbon fibers@NiS/Ni3S4@MoS2 with core-sheath structure for high efficiency and wide-bandwidth microwave absorption

Numerous studies have focused on the preparation of carbon fibers (CFs)-based high-efficiency microwave absorbers with reasonable structural design and surface morphology control, which simultaneously meet the required impedance matching and loss ability. Here, CFs@NiS/Ni₃S₄@MoS₂ (CNNM) with core-sheath structure was prepared through several simple hydrothermal reactions. The morphology of the as-prepared CNNM nanocomposite is controlled by the amount of added sodium molybdate dihydrate, which causes the difference in minimum reflection loss (RL) and effective attenuation bandwidth among the samples. For the microwave absorbing performance, the minimum RL is ?18 dB and the effective attenuation bandwidth is 8.7 GHz, which appear at the thickness of 2.8 mm and cover most of the X- and Ku-bands. The excellent absorbing performance is attributed to optimized impedance matching and enhanced polarization loss. These results originate from the transition metal sulfides, which not only effectively prevent the skin effect by decreasing the conductivity of CFs but also increase interfaces and flaws, leading to interface polarization and dipole polarization losses.